CREST AUDIO Pro 9200 Professional Power Amplifier

Designed with touring sound professionals in mind, the Crest Pro 200 Series power amplifiers faithfully produce high power with low distortion in an extremely lightweight economical package. Rock stable in stereo or bridged mode operation this series is engineered to exceed expectations, when powering multiple or single loudspeaker enclosures down to a 2 ohm load. The Pro 200 Series offer the protection that ensures safe & trouble free shows night after night.

Absolute sonic accuracy is the hallmark of every Crest amplifier. Bass is solid and defined to the limits of audibility with ample current reserves. Wide-bandwidth output devices ensure detailed, transparent high frequency response. And, thanks to Crest’s exclusive IGM™ circuit, the Pro 200 Series will drive 2 Ohm loads safely without compromising performance.

CREST AUDIO Pro 9200 FEATURES:

Dramatically reduced net weight
Latest generation of high speed, wide-bandwidth output devices
Dual, variable speed fans
Balanced XLR inputs
Speakon® and 5-way binding post speaker outputs
Mode selector switch for stereo, parallel and bridged-mono operation
Input sensitivity selection
Recessed, stepped attenuators
Front panel circuit - breaker switch
Five year warranty*

TOURCLASS/PROTECTION CIRCUITS

-ACL™ (Active Clip Limiting) prevents speaker damage by providing gentle gain reduction when the signal approaches the clipping threshold.

-IGM™ (Instantaneous Gain Modulation) monitors speaker loads to detect conditions that may overstress output devices. This allows safe operation into nominal 2 Ohm speaker loads.

-AUTORAMP™ gradually increases gain to the attenuator level settings when the amplifier is turned on. This prevents abrupt turn-on level.

-Other protection features include: short circuit, DC voltage, comprehensive thermal management and current in-rush turn-on/off; transient sub-sonic input.

CREST AUDIO Pro 9200 POWER SPEC:
		8 Ohm Stereo	4 Ohm Stereo	2 Ohm Stereo	8 Ohm Bridged	4 Ohm Bridged
1kHz, <0.05% THD+N:	.......	1300 W	2200 W	3250 W	4400 W	6500 W

CREST AUDIO Pro 9200 GENERAL SPECS:
Max RMS Output Voltage:	.......	113 V / Channel
Frequency Response:	.......	10 Hz - 100 kHz (+ 0 dB / - 2dB @ 1 Watt)
Power Bandwidth :	.......	10 Hz – 35 kHz; +0, -2 dB at rated 4 Ohm power
THD+N:	.......	<0.2% rated power @ 4 ohms, 1kHz
SMPTE IMD:	.......	<0.35% @ -3 dB below rated power @ 8 ohms, 4:1 (60Hz - 7kHz)
Damping Factor:	.......	>300:1 @ 8 ohms (20 Hz to 1000 Hz)
Gain:	.......	selectable between x40 (32 dB) and x20 (26 dB)
Input Sensitivity:	.......	2.35V (x40, 4 Ohm rated power +/- 3%)
Input Impedance:	.......	15k Ohm Balanced
Class:	.......	H
Input Connectors:	.......	balanced female XLR
Output Connectors:	.......	Speakon® connectors and five-way binding post
Power Supply:	.......	Switched Mode
Current Draw @ 120 VAC:
1/8 Power Draw:	.......	2200 Watts / 18.4A @ 4 Ohms 3350 Watts / 27.9A @ 2 Ohms
1/3 Power Draw:	.......	5000 Watts / 41.7A @ 4 Ohms 7.00 Watts / 60.9A @ 2 Ohms
Thermal Emissions:	.......	24,909 BTU/hr (1/3 power, 4 Ohm Bridged)
Cooling:	.......	Back to Front via 2 variable speed DC fan
Dimensions:	.......	3.5" H x 19" W x 12.25" D
Weight:	.......	24 lbs
Warranty:	.......	5 years *