The Turbosound TXD-151 is a passive trapezoidal 2-way loudspeaker with a 15"
low frequency driver and a 1" high frequency compression driver on a 70
x 40 high frequency horn in an easily transportable trapezoidal enclosure. Includes
two stage high frequency protection system to guard against HF driver overload.
Constructed from birch plywood, fitted with flush handles, pole mount socket
and rubber feet, internal M10 rigging points and two Speakon NL4MP connectors.
The Turbosound TXD-151 consists of a 15” reflex-loaded
low frequency driver and a 1” high frequency compression driver
on a 70°H x 40°V dispersion HF horn in an optimally tuned trapezoidal
enclosure. These high grade components are matched with an internal passive
crossover network to ensure a seamless transition between the HF and LF
drivers.
CROSSOVER & HF PROTECTION:
The crossover of the Turbosound TXD-151 incorporates a two-stage thermal
overload protection system which prevents damage to the high frequency
driver, reacting instantly to large transient peaks while still allowing
wide dynamic range to be maintained. Although the protection system is
transparent at normal operating levels, as the level increases the signal
is gradually and imperceptibly compressed once the critical threshold
has
been reached.
CONSTRUCTION:
The Turbosound TXD-151 cabinet is constructed from 15mm (5/8”) birch
plywood, screwed and glued together for maximum rigidity. A pole mount
socket is fitted for use with optional 35mm poles and loudspeaker stands.
Two recessed flush handles are provided for easy lifting and carrying
and four rubber feet are fitted to the bottom of the cabinet.. A grey
powder-coated perforated steel mesh grille protects the drive units from
damage.
RIGGING:
Rigging points are provided on the top and rear of the cabinet to enable
the Turbosound TXD-151 to be suspended and angled in permanent installations
using shoulder eyebolts. Rigging points are provided on the rear of the
cabinet for use with Turbosound and OmniMount™ wall and ceiling
brackets. Two Neutrik Speakon NL4MP speaker connectors are located on
the rear panel, providing input and parallel connections to additional
Turbosound TXD series cabinets or bass enclosures. |
|
TURBOSOUND TXD-151: GENERAL
SPECS: |
Dimensions: |
...... |
652mm x 465mm x 4230mm (25.7”
x 18.3” x 16.7”) |
Net
Weight : |
...... |
28kg (61.6lbs) |
Components: |
...... |
1 x 15” (381mm) LF driver, 1 x 1”
(25mm) HF compression driver |
| Frequency Response: |
...... |
45Hz - 20kHz +/- 4dB |
Nominal
Dispersion: |
...... |
70 deg H x 40 deg V @ -6 dB points |
| Power Handling: |
...... |
300 watts r.m.s., 600 watts program
Recommended amplifier power 600 watts @ 8 ohms |
Sensitivity: |
...... |
99 dB @ 1 Meter |
Maximum
SPL : |
...... |
124 dB Continuous, 130 dB Peak |
| Nominal Impedance: |
...... |
8 Ohms |
| Crossover: |
...... |
Internal passive network at 3kHz; 12dB/octave
high-pass, 12dB/octave low-pass |
| Construction: |
...... |
15mm (5/8”) birch plywood; rebated, screwed
and glued. Finished in TurboBlue™ semi-matt textured paint (optional
black textured paint). Two recessed carrying handle. Integral pole mount
socket |
| Grille: |
|
Heavy Duty powder coated perforated steel mesh |
| Connectors: |
...... |
(2) Neutrik Speakon NL4MP, wired pin1+: positive,
pin 1-: negative, pins 2+ and 2- N/C |
| Flying Hardware: |
...... |
(3) M10 internal threaded rigging points
(4) M8 internal threaded rigging points for WB-55 and CB-55 brackets |
| Spares & Accessories: |
...... |
LS-1521 15” (381mm) LF loudspeaker
RC-1521 Recone kit for LS-1521
CD-111 1” (25mm) HF compression driver
RD-111 Replacement diaphragm for CD-111
MG-151/X Replacement grille
PX-151/X Passive crossover network
WB-55 Wall bracket
CB-55 Ceiling bracket
PB-55 Pole mount bracket |
